Quality and measurement
procedure standards

 

SCAN-P 70:09 - T569 (TAPPI)
   

SCAN-P 70:09
DIN 19303

DIN 55437-1

EN 1230-2

ISO 10399
ISO 11475
ISO 11556
ISO 1924-2

ISO 1974   
ISO 2470-2

ISO 2471

ISO 2493
ISO 2758
ISO 287
ISO 3783

ISO 4120
ISO 534   
ISO 535
ISO 536
ISO 5495
ISO 5628

ISO 5629
ISO 5631-2

ISO 6588-1
ISO 8254-1

ISO 8791-2

ISO 8791-4

ISO 9895
ISO/IEC 17025

RTM 30 (Paper Federation )
T459 (TAPPI)
T558 (TAPPI)

T569 (TAPPI)

 

Ink absorbency value
Karton - Begriffe und Sorteneinteilungen, Paperboard - Terms and grades
Testing of board - Creasings - Part 1: Laboratory producing of test creasings
paper and board intended to come into contact with foodstuffs - sensory analysis - part 2: off-flavour (taint)
Sensory analysis - Methodology - Duo-trio test
Determination of CIE whiteness, D65/10 degrees (outdoor daylight)
Determination of curl using a single vertically suspended test piece
Determination of tensile properties -- Part 2: Constant rate of elongation method (20 mm/min)
Determination of tearing resistance (Elmendorf method)
Measurement of diffuse blue reflectance factor -- Part 2: Outdoor daylight conditions (D65 brightness)
Determination of opacity (paper backing) - Diffuse reflectance method
Determination of resistance to bending
Determination of bursting strength
Determination of moisture content of a lot -- Oven-drying method
Determination of resistance to picking - Accelerated speed method using the IGT-type tester (electric model)
Sensory analysis - Methodology - Triangle test
Determination of thickness, density and specific volume
Determination of water absorptiveness - Cobb method
Determination of grammage
Sensory analysis - Methodology - Paired comparison test
Determination of bending stiffness by static methods - General principles
Determination of bending stiffness - Resonance method
Determination of colour by diffuse reflectance - Part 2: Outdoor daylight conditions (D65/10 degrees)
Determination of pH of aqueous extracts - Part 1: Cold extraction
Measurement of specular gloss - Part 1: 75 degree gloss with a converging beam, TAPPI method
Determination of roughness/smoothness (air leak methods) - Part 2: Bendtsen method
Determination of roughness/smoothness (air leak methods) - Part 4: Print-surf method
Compressive strength - Short-span test
General requirements for the competence of testing and calibration laboratories
Surface Strength of Paper (Wax Pick Test)

Surface Strength of Paper (Wax Pick Test)
Surface wettability and absorbency of sheeted materials using an automated contact angle tester
Internal bond strength (Scott type)

Ink absorbency value
Karton - Begriffe und Sorteneinteilungen, Paperboard - Terms and grades
Testing of board - Creasings - Part 1: Laboratory producing of test creasings
paper and board intended to come into contact with foodstuffs - sensory analysis -
part 2: off-flavour (taint)
Sensory analysis - Methodology - Duo-trio test
Determination of CIE whiteness, D65/10 degrees (outdoor daylight)
Determination of curl using a single vertically suspended test piece
Determination of tensile properties -- Part 2: Constant rate of elongation method
(20 mm/min)
Determination of tearing resistance (Elmendorf method)
Measurement of diffuse blue reflectance factor -- Part 2: Outdoor daylight conditions
(D65 brightness)
Determination of opacity (paper backing) - Diffuse reflectance method
Determination of resistance to bending
Determination of bursting strength
Determination of moisture content of a lot -- Oven-drying method
Determination of resistance to picking - Accelerated speed method using the IGT-type tester (electric model)
Sensory analysis - Methodology - Triangle test
Determination of thickness, density and specific volume
Determination of water absorptiveness - Cobb method
Determination of grammage
Sensory analysis - Methodology - Paired comparison test
Determination of bending stiffness by static methods - General principles
Determination of bending stiffness - Resonance method
Determination of colour by diffuse reflectance - Part 2: Outdoor daylight conditions (D65/10 degrees)
Determination of pH of aqueous extracts - Part 1: Cold extraction
Measurement of specular gloss - Part 1: 75 degree gloss with a converging beam,
TAPPI method
Determination of roughness/smoothness (air leak methods) - Part 2: Bendtsen method
Determination of roughness/smoothness (air leak methods) - Part 4: Print-surf method
Compressive strength - Short-span test
General requirements for the competence of testing and calibration laboratories
Surface Strength of Paper (Wax Pick Test)
Surface Strength of Paper (Wax Pick Test)
Surface wettability and absorbency of sheeted materials using an automated contact angle tester
Internal bond strength (Scott type)

Contact

Iggesund Paperboard
825 80 Iggesund
Sweden

+46 650 - 280 00
info@iggesund.com

Connect with Iggesund

  • Holmen.com
  • Cookies
  • MyPages
  • Print

© Iggesund 2016